# Crafit 3D Printer Cabinet Review: Worth $499 or DIY?

Crafit 3D printer cabinet review: printer fit, a measured 8 to 10 dB noise drop, ventilation and filament storage, plus what a DIY enclosure would cost.

- Author: Chris Hoffman (Hoffman Engineering)
- Published: 2024-12-11
- Category: Other
- Video: https://www.youtube.com/watch?v=U9Io3zToJoA
- Web page: https://www.hoffman.engineering/blog/crafit-3d-printer-cabinet-review-worth-499-or-diy/

## Summary

- Product: Crafit 3D Printer Cabinet
- Price: $499 at time of review
- Verdict: A sturdy, well-lit enclosure with built-in ventilation that takes the edge off printer noise. Measure your printer's full range of motion first, because large bed slingers won't fit with the doors closed.

Your 3D printer deserves better than the corner of a desk collecting dust. The **Crafit 3D Printer Cabinet** gives it a dedicated, fully enclosed home with lights, an exhaust fan, a temperature and humidity readout and storage for eight spools of filament. In this Crafit 3D printer cabinet review I test which printers fit, measure how much quieter it makes them, and price out a DIY enclosure to see whether the $499 cabinet is worth it.

## Three Sections, One Cabinet

The Crafit cabinet stands **23.6 x 23.2 x 68.9 inches** and is built from a steel frame, wood panels and clear acrylic. It splits into three areas: an open wire shelf at the bottom for tools, the enclosed printer chamber in the middle, and an enclosed filament section on top.

The printer chamber is the star. Two acrylic doors swing open a full 180 degrees and close with magnets at the top and bottom. The doors are 4mm acrylic and the sides are 1.5mm. LED strips light the printer from overhead and behind, and the control panel up top shows temperature and humidity and runs the light and exhaust fan.

Inside there's a three-outlet power strip. The control panel takes one outlet, which leaves two for your printer and an accessory like a Raspberry Pi.

## Will Your 3D Printer Fit?

The chamber takes printers up to **22 inches deep, 21.6 inches wide and 28.7 inches tall**. I tested the Anycubic Kobra 2 Neo, Longer LK4X, Elegoo Neptune 4 Pro, [Two Trees SK1](https://www.hoffman.engineering/blog/700-mm-s-klipper-corexy-tilt-bed-leveling-this-has-it-all-twotrees-sk1-3d-printer-review/) and Anycubic Photon Mono M5, and they all fit.

Bed slingers are where you need to be careful. Measure the full space the printer uses while it runs, not only the frame. My bed slingers with beds of 220mm or smaller fit. The Anycubic Kobra 3, Creality Ender-3 V3 Plus and Artillery Sidewinder X3 Plus all needed too much room for the bed to travel with the doors shut.

## Ventilation for Resin and ABS

The exhaust fan is **4.5 inches in diameter** and rated to blow at 4.2 meters per second (9.4 mph). It comes with a **7 foot duct**, so venting out a window is easy. I prefer connecting it to an air purifier to filter out particles and fumes.

That makes the cabinet a good fit for smelly materials like ABS, and even more for resin printers, which put out a lot of fumes. The built-in ventilation helps keep them out of the room.

## Filament Storage and Passthrough

The top section sits behind its own magnetic doors and holds **up to 8 spools**. Two holes pass filament down into the printer chamber, so the four inner spool holders work as live feeds while you print. You can also move two holders onto the roof of the printer section to hang four spools right above your printer.

Down at the bottom, the metal wire shelf is handy for keeping tools close.

## Assembly

The cabinet ships flat-packed in one box. The instructions estimate about 90 minutes, and that was about right for me. Every screw and tool is numbered, and each step calls out which bag to use.

Two things slowed me down. One bottom section was too thick from its paint and needed some gentle persuasion to fit. And the protective film on the doors was trapped inside the frame, so instead of peeling cleanly it ripped at the edges, and I had to go around with a knife to clean it up. Once it's together, adjustable feet let you level the cabinet.

## Noise, Vibration and Chamber Temperature

With the doors closed I measured about an **8 to 10 decibel** drop in noise while printing. It doesn't make the printer silent, but it takes the edge off, especially the harsher cooling fan sounds at high speed. Crafit advertises a 20 to 30 decibel drop, which isn't close. Still, 10 decibels is significant if you share the room with your printer.

The cabinet stayed sturdy during fast printing. The thin acrylic sides wobble a bit, but the vibration didn't cause any noise, and it's sturdier than many desks I've kept printers on.

The enclosure also blocks drafts and holds heat. After about 4 hours of printing, the thermometer read **87 degrees**, which helps with warp-prone materials like ABS.

## Can the Filament Section Work as a Dry Box?

I'm a big believer in keeping filament in a dry box, so I hoped the top section could be one. I put my rechargeable dehumidifier and a hygrometer inside and watched it for a day. The gaps around the doors were too large, and the humidity never dropped below the room's.

Weather stripping might seal it up. As it ships, though, I wouldn't keep rolls in there long-term if moisture is a concern.

The control panel's hygrometer has a related problem. It measures the printer chamber, not the filament section, and the exhaust fan pulls fresh air through the chamber constantly. It's neat to see the number, but it doesn't tell you much you can act on.

## Crafit Cabinet vs a DIY Enclosure

The Crafit cabinet was **$499** when I reviewed it. Sales came and went during testing, and at one point an Amazon Prime discount of $100 and an extra $30 coupon brought it down to $370.

To see if building your own is cheaper, I priced one around the IKEA BROR shelves my printers sit on:

- **Shelf:** $95
- **Acrylic:** about 6,400 square inches of the thinnest panels I could find locally (3/32 inch), $221 to $244
- **Exhaust fan:** $35, plus $15 for a 4 inch duct
- **Thermometer and hygrometer, LED lights, power strip:** $10 each
- **Door pulls, magnets and plates:** $15

That adds up to **$411 to $435** in parts, before the time to design and build it. JKSniper's popular aluminum extrusion enclosure costs 25 euros for the plans, and its creator estimates 300 to 400 euros in materials for the default configuration. That's roughly $315 to $420, and you still have to print the brackets and cut and assemble everything.

You might save a little going DIY, but you'll spend a lot more time. Crafit has done that work for you.

## Verdict: Should You Buy the Crafit 3D Printer Cabinet?

The Crafit 3D Printer Cabinet is a great addition to a home or workshop. It makes your printer the center of attention with its own dedicated space, and it's functional: the enclosure keeps dust, pets and little hands out and holds heat in, the noise drop is welcome, and the active ventilation is a big plus for resin printers.

The one thing you must do first is measure your printer's full working space. If it fits, this is an excellent piece of furniture for a 3D printing enthusiast. The only flaw I found in the hardware was one broken door magnet, fixed with superglue.

At $499 it's a compelling purchase, and a sale price on top of that makes it an easy decision if you're looking for a home for your printer. [Check the latest price on Amazon](https://amzn.to/41sDzd1).

## Pros and cons

### Pros

- Doors closed, printer noise dropped about 8 to 10 dB and the harsh fan sounds lost their edge
- Built-in 4.5 inch exhaust fan and 7 foot duct vent fumes from resin or ABS out a window or into an air purifier
- Chamber reached 87 degrees after about 4 hours of printing, which helps materials like ABS that warp
- Bright LED lighting from overhead and behind, plus a temperature and humidity readout
- Sturdy enough for high-speed printing, with a little wobble from the thin side panels
- Numbered bags and clear instructions. Assembly took about the 90 minutes the manual says
- Keeps dust, pets and little fingers away from the printer

### Cons

- Bed slingers with beds larger than 220mm needed too much room to run with the doors shut
- The filament section isn't airtight, so a dehumidifier never got it below room humidity
- Measured noise reduction is far short of the advertised 20 to 30 dB
- The hygrometer reads the printer chamber, not the filament section, so it isn't very actionable
- Protective film on the doors tore at the edges and had to be trimmed out with a knife
- One door magnet arrived broken and needed superglue

## Specs

| Spec | Value |
| --- | --- |
| Outer Dimensions | 23.6 x 23.2 x 68.9 in |
| Printer Area | Fits printers up to 22 in deep, 21.6 in wide and 28.7 in tall (including the bed's travel) |
| Construction | Steel frame, wood panels, clear acrylic doors (4mm) and sides (1.5mm) |
| Sections | Open wire storage shelf, enclosed printer chamber, enclosed filament storage |
| Filament Storage | Spool holders for up to 8 rolls, with 2 passthrough holes into the printer chamber |
| Ventilation | 4.5 in exhaust fan rated at 4.2 m/s, with a 7 ft duct |
| Control Panel | Thermometer, hygrometer, light and fan controls |
| Power | Built-in 3-outlet power strip (one used by the control panel) |
| Noise Reduction (measured) | About 8 to 10 dB with the doors closed. Crafit advertises 20 to 30 dB |

## Where to buy

- [Crafit 3D Printer Cabinet](https://amzn.to/41sDzd1): $499

Prices may have changed since this review.

## FAQ

### Is the Crafit 3D printer cabinet worth it?

At $499 it is a compelling purchase if your printer fits, and sale prices make it an easy call. I priced a comparable DIY build from an IKEA BROR shelf, acrylic panels and the same features at $411 to $435 in parts alone, before the time to design and build it.

### What 3D printers fit in the Crafit cabinet?

The printer area takes printers up to 22 inches deep, 21.6 inches wide and 28.7 inches tall. The Anycubic Kobra 2 Neo, Longer LK4X, Elegoo Neptune 4 Pro, Two Trees SK1 and Anycubic Photon Mono M5 all fit. The Anycubic Kobra 3, Creality Ender-3 V3 Plus and Artillery Sidewinder X3 Plus beds needed too much room to run with the doors closed. Measure your printer's full range of motion before you buy.

### How much quieter is a 3D printer inside the Crafit cabinet?

I measured about an 8 to 10 decibel reduction with the doors closed. It doesn't make a printer silent, but it takes the edge off cooling fan noise at high speeds. Crafit's advertising claims 20 to 30 decibels, which I didn't come close to.

### Can the Crafit cabinet keep filament dry?

Not as it ships. With a rechargeable dehumidifier and a hygrometer in the top section, humidity never dropped below the room's because the gaps around the doors are too large. Weather stripping might seal it, but I wouldn't store filament there long-term if moisture is a concern.

---

This Crafit 3D Printer Cabinet was provided by Crafit for review. Crafit did not pay for this review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.
