# Creality K1C Review: Printing Carbon Fiber Nylon Made Easy

Creality K1C hands-on review after a month of testing. 600mm/s CoreXY speed, a hardened steel hotend and real carbon fiber nylon prints. Is it worth it?

- Author: Chris Hoffman (Hoffman Engineering)
- Published: 2025-08-07
- Category: 3D Printers
- Video: https://www.youtube.com/watch?v=uJI5dkS5oo0
- Web page: https://www.hoffman.engineering/blog/creality-k1c-review-carbon-fiber-nylon-made-easy/

## Summary

- Product: Creality K1C
- Price: $499 at time of review
- Verdict: A fast, fully enclosed CoreXY printer that handles carbon fiber PLA and carbon fiber nylon out of the box. A strong pick if you want abrasive filaments without babysitting your nozzle, as long as 220 x 220 x 250mm is big enough for you.

The **Creality K1C** is a fully enclosed CoreXY 3D printer built to handle abrasive filaments, from carbon fiber PLA all the way to carbon fiber nylon. I spent a month with it, printing a 15-minute Benchy, torture tests, a full-height bust and a set of carbon fiber clamps. This hands-on Creality K1C review covers the hardware, the software, the print results and the one quirk you should know about before you buy.

## What Makes the K1C Different: The Hardened Steel Hotend

The K1C is the upgraded version of the Creality K1, and the C stands for carbon. The headline change is the hotend. It uses a **quick-swap tri-metal nozzle**: a hardened steel tip, a copper heat block and a titanium heat break. The copper heats up fast and holds temperature steady, while the titanium break keeps heat from creeping up and causing clogs.

That hotend reaches **300°C**, and the steel tip stands up to abrasive filaments that would chew through a brass nozzle. Carbon fiber is the obvious one, but glow-in-the-dark and pure white filaments are abrasive too. With the K1C you can print those without worrying about wearing out your nozzle.

Feeding it is a **direct drive extruder**. It grips the filament well and keeps that grip even at the printer's top speed of 600mm/s.

## CoreXY Speed: 600mm/s in Practice

The K1C uses a CoreXY motion system. Two stationary motors work together through a belt loop to move the hotend in X and Y, and their combined torque gives a rated max acceleration of **20,000mm/s²** and a max print speed of **600mm/s**.

Those numbers hold up. I found the K1C to be a very fast printer, and it pushed high-speed PLA to 500 and 600mm/s without complaint.

The bed moves in Z, with a single motor and a belt under the bed turning the three threaded rods that support it. Build volume is **220 x 220 x 250mm**, and the heated bed goes up to 100°C.

## Automatic Bed Leveling and Build Plate

Load sensors built into the bed handle **fully automatic bed leveling** and nozzle offset. You can throw away your leveling paper. The K1C runs those calibrations itself and gives you a good first layer every time.

The build plate is a removable, magnetic, flexible PEI spring steel sheet. It ships with a double-sided smooth plate meant for PLA, and Creality sells a textured PEI plate separately. Creality recommends using the included glue stick with the smooth plate, and that combination worked perfectly for me. I had zero failures from bed adhesion, and once a print cooled, a quick flex of the plate popped it right off.

## Enclosure, Cooling and Filtration

The K1C is fully enclosed. The clear plastic lid is removable, so you can take it off for PLA or set it back on (it's held magnetically) for materials that are sensitive to temperature and drafts. The glass door is magnetic too, and white LEDs light up the interior.

There's no dedicated chamber heater, but with the door and lid closed the chamber reaches about **50°C**.

A strong auxiliary cooling fan on the right side blows across the top layers of the print. It keeps overhangs and bridges solid even at 600mm/s.

The enclosure also has a chamber exhaust fan with an **activated carbon filter**. Activated carbon is good at removing smells and fumes, so it likely cuts down on VOCs, and it's great for smelly materials like ABS. There's no HEPA filter in the mix, though, so I can't say how well it handles particles.

## Touch Screen, Noise and Klipper Firmware

Up front is a **4.3 inch color touch screen**. It's responsive and the menus are well organized. During a print you can skip individual objects, which is handy for batch printing: if one part fails, you skip it instead of canceling the whole plate.

The K1C is a quiet printer even at high speed. If you need it quieter, Quiet Mode slows the print down a lot but drops the noise to **45 decibels**.

Under the hood it runs **CrealityOS, Creality's version of Klipper firmware**. The printer uses its built-in accelerometers to calibrate input shaping automatically. It runs a frequency sweep on X and Y, measures how the frame vibrates, and uses that to drive the motors in a way that removes ghosting around hard edges. Pressure advance helps with smoother, more accurate top surfaces.

Built-in Wi-Fi lets you send and start jobs wirelessly, monitor the printer remotely and install firmware updates over the air.

## Assembly: 20 Minutes to the First Print

The K1C arrives mostly assembled. Pull out the packing material and remove the few screws holding the bed and the XY gantry. A couple of screws attach the door handle, then you slide the air filter and spool holder into the back.

On first power-up the printer walks through a self-check and starts its calibration on its own: auto bed leveling and the input shaping frequency sweep. From unboxing to the first print took me **20 minutes**, and the whole process was smooth.

## Creality Print Slicer and the Built-In Camera

Creality recommends **Creality Print**, its fork of Orca Slicer. Adding the K1C means picking it from the list, and you get "standard" and "high quality" profiles for a range of layer heights and materials. The built-in profiles worked great. They feel tuned to this printer and they aren't shy about using its speed. Once you slice, you can send the job and start it wirelessly, and the slicer switches to a device tab where you can watch it.

The **built-in camera** is one of the nicer ones I've used. Picture quality is great and the frame rate is smooth. It also records timelapses, taking a frame at the start of each layer, so they often run a couple of minutes long. One tip: peel the protective film off the lens first, or your timelapses will come out blurry.

## Print Quality Results: Benchy, Torture Test and Bust

Sunlu provided the filament for these tests, including its [high-speed marble PLA](https://store.sunlu.com/products/high-speed-pla-marble-3d-printer-filament-1kg?_pos=1&_sid=8fdc65e42&_ss=r&variant=49959995179290&sca_ref=6509515.9CIaM1NpXK&sca_source=k1c).

- **15-minute Benchy:** the included speed Benchy finished in 15 minutes with consistent layers and good bridges and overhangs. There's a slight hull line where the deck's top layers begin, but for a 15-minute Benchy it's a great showing.
- **Autodesk Kickstarter torture test (PLA):** the longest bridge is perfect and the 15 degree overhang looks great. A few light wisps of stringing on the top pillars, but every pillar printed to full height.
- **Desert Kiss dice tower:** printed at 0.16mm layers. Consistent layers, and every overhang printed without supports.
- **Brick dice tower:** in Sunlu's brick red PLA, the bottom of the staircase and each pillar came out clean. The only flaw was some light wisps between a few pillars in the middle section.
- **Captain America bust:** printed at the full height of the build volume. Under harsh edge lighting you can find a little ringing on a few hard edges, but not on most of them, so input shaping is doing its job. It even handled the overhang under the chin.

## Carbon Fiber PLA and Carbon Fiber Nylon on the K1C

Abrasive filament is the reason the K1C exists, so I tested two: **Creality Carbon Fiber PLA** and **Polymaker Fiberon PA612-CF** carbon fiber nylon.

Carbon fiber PLA was easy. Creality Print includes PLA-CF profiles, slicing was simple, and the prints came out great. I love the matte finish.

Carbon fiber nylon put up more of a fight. I first tried feeding it straight from my EIBOS Polyphemus filament dryer, but the angle from my shelf wasn't good. Once I loaded the nylon from the K1C's own spool holder, it printed perfectly. Nylon absorbs moisture fast, so print from a dryer or dry box if you can.

The K1C handled the **300°C print temperature** without issues, and the nylon stuck well to the smooth plate. With both carbon fiber filaments, this printer was a beast.

PETG works well too. I've been using it to print Gridfinity bins, and they turned out great.

## The One Issue: Purge Line and a Kinked Bowden Tube

I ran into one problem in a month of testing. The bowden tube runs through a cable chain from the hotend to the spool holder at the back. The default slicer profiles print a purge line at the far left of the bed, and that move pushes the cable chain up against the lid.

A rubber strip on the lid prevents noise or damage, but the movement can kink the bowden tube sharply during the purge. PLA and PETG didn't care. My carbon fiber nylon, which is brittle, snapped every time.

So if your filament keeps breaking, watch for that kink and move or remove the purge line in the start G-code of your profiles.

## Verdict: Should You Buy the Creality K1C?

The Creality K1C is a worthy upgrade over the original K1. It keeps most of the K1's features and adds a hotend and extruder that can print high-temperature abrasive filaments. Carbon fiber might be niche for you, but the same hardware lets you run glow-in-the-dark or pure white filament without worrying about nozzle wear. It's fast, with Creality's profiles happily using the 600mm/s top speed, and the built-in camera is a highlight. I do wish the build volume were bigger, though 220 x 220 x 250mm covers most needs.

Creality earned a reputation for tinkering back in the Ender 3 days. With its Klipper-based printers like this one, my experience has been excellent: almost no assembly, automatic calibration on first boot and great prints. Apart from the purge line kink, which has a simple fix, nothing came up in a month of printing that would stop me from recommending it.

When I recorded the review, the K1C was on sale for $559, about $50 more than the original K1. Creality now lists it at **$499**. If you want a fully enclosed printer that can handle abrasive materials, the K1C could be the printer for you.

[Check the latest price on the Creality K1C](https://crealityofficialstore.sjv.io/k42700)

## Pros and cons

### Pros

- Hardened steel tri-metal hotend reaches 300°C and printed carbon fiber PLA and carbon fiber nylon without trouble
- Fast. High-speed PLA ran at 500 to 600mm/s and the included Benchy finished in 15 minutes
- Fully automatic bed leveling, nozzle offset and input shaping calibration on first power-up
- 20 minutes from unboxing to the first print
- Built-in camera with good picture quality, a smooth frame rate and decent timelapses
- Quiet even at speed, with a Quiet Mode that drops it to 45 dB
- Creality Print profiles are well tuned and use the printer's speed
- No bed adhesion failures with the smooth PEI plate and the included glue stick

### Cons

- The default purge line pushes the cable chain into the lid and kinks the bowden tube, which snapped brittle carbon fiber nylon every time
- Build volume of 220 x 220 x 250mm is on the small side
- Activated carbon filter only, with no HEPA filter for particles
- No dedicated chamber heater, so the chamber tops out around 50°C
- Ships with a smooth plate only. A textured PEI plate is sold separately
- Slight ringing on a few hard edges and light stringing on tall pillar models

## Specs

| Spec | Value |
| --- | --- |
| Build Volume | 220 x 220 x 250mm |
| Max Speed | 600mm/s (high-speed PLA ran cleanly at 500 to 600mm/s in testing) |
| Max Acceleration | 20,000mm/s² |
| Hotend | Quick-swap tri-metal, hardened steel nozzle, up to 300°C |
| Extruder | Direct drive |
| Bed | Heated to 100°C, magnetic flexible PEI spring steel plate (smooth, double-sided) |
| Leveling | Automatic, using load sensors in the bed (also sets nozzle offset) |
| Enclosure | Fully enclosed, removable lid, about 50°C chamber with no dedicated heater, activated carbon exhaust filter |
| Firmware | CrealityOS (Klipper based), automatic input shaping |
| Screen | 4.3 inch color touch screen |
| Camera | Built in, live view and timelapses |
| Connectivity | Wi-Fi |
| Noise | 45 dB in Quiet Mode |

## Where to buy

- [Creality K1C at Creality](https://crealityofficialstore.sjv.io/k42700): $499
- [Creality K1C on Amazon](https://amzn.to/4ofiFXU)

Prices may have changed since this review.

## FAQ

### Is the Creality K1C worth it?

If you want a fully enclosed CoreXY printer that can run abrasive filaments, yes. In a month of testing I hit one issue, a purge line that kinked the filament path, and it has a simple fix. It was $559 on sale when I recorded the review and is $499 at Creality now.

### Can the Creality K1C print carbon fiber nylon?

Yes. I printed Polymaker Fiberon PA612-CF at 300°C on the smooth PEI plate and it came out great. Load it from the rear spool holder (or a dryer with a clean path), keep it dry, and move or remove the far-left purge line in the start G-code so the bowden tube doesn't kink and snap the filament.

### How fast is the Creality K1C in practice?

Creality rates it at 600mm/s with 20,000mm/s² acceleration, and I could push high-speed PLA to 500 and 600mm/s. The included speed Benchy finishes in 15 minutes with consistent layers and good overhangs.

### What is the difference between the Creality K1C and the K1?

The K1C adds a hardened steel quick-swap hotend for abrasive filaments and includes a camera. Most other features carry over from the K1. When I recorded the review the K1C was about $50 more than the original K1, and I think the upgrades are worth it.

### Why does filament keep breaking on my Creality K1C?

Check the purge line. The default start G-code purges at the far left of the bed, which pushes the cable chain into the lid and sharply bends the bowden tube. PLA and PETG survived it, but carbon fiber nylon broke every time. Moving or removing that purge fixes it.

---

This Creality K1C was provided by SainSmart for review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.
