# HansMaker F1 Pro Review: Stainless Colors Without MOPA

HansMaker F1 Pro review: a 20W fiber laser tested a month on brass, aluminum, stainless colors, steel cutting, acrylic and slate. See results and setup tips.

- Author: Chris Hoffman (Hoffman Engineering)
- Published: 2025-08-11
- Category: Lasers
- Video: https://www.youtube.com/watch?v=AQ8pAJh9Jzc
- Web page: https://www.hoffman.engineering/blog/hansmaker-f1-pro-review-stainless-colors-without-mopa/

## Summary

- Product: HansMaker F1 Pro 20W
- Verdict: A strong first fiber laser from HansMaker, with stainless steel colors I'd only seen from MOPA lasers, deep brass engraving and a LightBurn Pro license in the box. Plan on starting every job from your computer, since there's no foot pedal or start button.

The **HansMaker F1 Pro** is a **20W fiber laser** that sold for $1,479 at the time of recording, and after a month of testing it gave me deep engraved brass coins, cleanly cut steel gears and stainless steel colors I'd only seen from MOPA lasers. This HansMaker F1 Pro review covers the hardware, the LightBurn setup step you can't skip, and how it handled aluminum, brass, stainless steel, black acrylic and slate.

## What the HansMaker F1 Pro 20W Fiber Laser Can Do

The F1 Pro produces a **1064nm infrared beam**, the wavelength that makes fiber lasers so good on metal. You can cut and engrave steel, aluminum, brass, titanium and more, and you can deep engrave thick pieces like custom brass coins. Most plastics work too, along with darker natural materials like stone and leather.

What it won't do: wood, or transparent materials like clear acrylic and glass. If those are your main projects, a fiber laser is the wrong tool.

HansMaker is a new brand. It comes from Hans Laser, a Chinese company known for industrial lasers, and it was created to bring that industrial experience to hobbyists and small businesses. The F1 Pro 20W is its first product.

## Galvo Speed and Pulse Frequency

Everything lives in the main body. The laser source fires through a pair of galvo mirrors, then down through the focusing lens onto your material. Those lightweight mirrors move fast, and HansMaker rates the F1 Pro at up to **10,000mm/s**.

You won't run it that fast most of the time, though. Every fiber laser is pulsed, and if you go too fast or set the frequency too low you'll see pulsing artifacts in the engraving. In my testing I usually ran between **1,000 and 4,000mm/s**, depending on the material.

The frequency range is a highlight. The F1 Pro adjusts from **5 to 150kHz**, which is wide for a non-MOPA fiber laser, and I always found a frequency that worked for each material I tested. Test speed and frequency on your own materials before you commit to a big job.

## Focusing with the Electric Lift and Red Laser

The laser sits on an **electric lifting stand**, controlled by two buttons on the laser. To focus, place your material underneath and move the head up or down until two red dots line up. That's it. There's no autofocus, but manual focus takes a second or two, and the dots always lined up exactly for me.

For positioning, an **inline red laser** shines through the same galvo and lens as the working laser. In the software you can trace the bounding box, the outer contour, or every individual shape in your design. I could see the red laser from every angle on every material I tested, and it lined up with the cutting laser with no offset, which isn't something I can say about every laser I've reviewed.

## Portability and Handheld Mode

You can use the F1 Pro three ways. Normally it rests on the lifting stand. If your object doesn't fit, remove the center of the stand and set the laser on top of the material. And for full portability, take the laser off the stand and use it handheld.

For handheld work, HansMaker includes a yellow **safety shield**. It blocks laser light, and it's sized so the laser is in focus at the bottom of the shield. Set the laser and shield on whatever you want to engrave and you're ready to go.

At **7.5kg** it's light for a fiber laser. But with everything in the head, it's a little hard to hold and position with one hand. The center of mass sits toward the back too, so it tips backward if you rest it on the shield alone. Not a big downside, but you'll notice it.

The bigger handheld limitation: there's no foot pedal or start button, so you have to start every job from your computer.

## Work Area, Precision and Ports

The included **110 field lens** gives a **110 x 110mm** work area. That's a medium size and a good balance between area and how tightly the beam is focused. HansMaker claims precision of up to 0.001mm. I can't test that directly, but the resolution is excellent, and photo engraving on black acrylic came out great.

The work area has a grid of threaded holes, so you can build alignment jigs and position parts the same way every time for batch jobs.

On top you'll find the handle with the power button, the lift buttons and a removable filter that's easy to clean. Around back there's a **USB Type-B** port for your computer, a USB port labeled SDS (likely for diagnostics), two RJ45 ports for the optional rotary and the lifting stand, and the main power input.

## Assembly and Safety

Setup is about as easy as it gets. Unpack the well-packed box, set the laser on the lifting stand, secure it with a single bolt, plug in the stand and the power brick, and you're done.

HansMaker includes a pair of safety glasses. Use them. A 20W fiber laser can cause permanent eye damage from direct or reflected light, so wear eyewear rated for 1064nm and read the manual to know which materials are safe to engrave.

## LightBurn Setup: Don't Skip the Calibration

The F1 Pro is built for **LightBurn**, and HansMaker includes a **LightBurn Pro license**, a $200 value. That matters, because HansMaker doesn't include other free software like EZCad and only provides LightBurn instructions.

The setup has one trap. You need to enter your machine's calibration values manually, and the paper manual doesn't mention LightBurn at all. HansMaker's online LightBurn guide is good, but the important step is at the very end, after pages explaining what every LightBurn button does. Your machine ships with a laser-engraved aluminum card listing its calibration values. Open **Device Settings** in LightBurn and enter them. Skip this and your shapes will come out distorted and the wrong size.

Once it's configured, the F1 Pro works great with LightBurn, and features like **3D Slice** mode make deep engraving 2.5D designs easy.

## Engraving Aluminum and Deep Engraving Brass

All of my tests ran with an OMTech fume extractor. I recommend an extractor for any fiber laser to pull particles and fumes out of the air. HansMaker doesn't sell one right now, so budget for one separately.

Metal is where the F1 Pro shines. **Coated aluminum** business cards engraved quickly, and every color of coated aluminum I tried worked well. On **bare aluminum** you can get dark marks, and with multiple passes you can engrave deep into an aluminum block.

**Brass** was the standout for deep engraving. My custom brass coins reached about **1.5mm deep in about an hour and a half**, a great result for a 20W fiber laser. The whole coin process, from engraving to polishing and weathering, has [its own guide](https://www.hoffman.engineering/blog/how-to-make-custom-brass-coins-with-a-fiber-laser/).

## Stainless Steel Color Engraving

This is the result that surprised me most. By adjusting power, line interval and frequency, I got **greens, magentas, blues, reds, purples** and a lot more on stainless steel. I've normally only seen that range from MOPA lasers. The F1 Pro might have the best stainless color results I've seen from a non-MOPA fiber laser.

## Cutting Thin Stainless Steel

The F1 Pro can also cut through metal. It went through **0.1mm stainless steel sheet in two passes** without major warping, and the steel gear I cut came out clean.

## Black Acrylic and Photo Engraving

On **black acrylic** the F1 Pro leaves a high-contrast white mark with no bubbling. My keychains came out sharp, and even the small text and tick marks on a ruler design looked good.

Photo engraving looks great too. I had to adjust brightness and contrast a few times to find the right settings, but a photo of my cat Sven turned out well.

## Engraving Slate Coasters

**Slate** gave me a nice range of effects. Multiple passes engrave deep, while a single pass at lower power leaves a bright white mark that looks great on a coaster.

## Verdict: Should You Buy the HansMaker F1 Pro?

For a company's first fiber laser, HansMaker got a lot right. Compared to other 20W fiber lasers, the F1 Pro performed near the top of its class in my testing. It deep engraved brass coins and aluminum blocks, cut thin steel sheet, and still had the accuracy for clean plastic and photo engraving. The stainless steel colors are the headline: oxide colors I'd only seen from MOPA lasers.

The F1 Pro makes the most sense if you engrave metal and want the flexibility to work on objects that won't fit under a stand. Handheld mode and the focusing shield make that easy. Skip it if you need to start jobs without a computer nearby, since there's no foot pedal or start button. And when you set it up, follow HansMaker's LightBurn guide all the way to the calibration step at the end.

At recording it was on sale for $1,479, less than many other 20W fiber lasers at the time, and the LightBurn Pro license adds to the value. When I checked HansMaker's store in November 2026, the listing didn't show a current price I could confirm, so check the link for current pricing and availability. If you're comparing 20W fiber lasers, my [EM-Smart Nova review](https://www.hoffman.engineering/blog/em-smart-nova-review-18-lb-fiber-laser-that-folds/) covers another one I tested.

[Check the latest price at HansMaker](https://hansmaker.com/collections/machine/products/hansmaker-f1-pro-20w-fiber-laser-engraver?aff=6)

## Pros and cons

### Pros

- Stainless steel colors (greens, magentas, blues, reds, purples) I'd normally only expect from a MOPA laser
- Deep engraved brass coins about 1.5mm deep in about an hour and a half
- Cut 0.1mm stainless steel sheet in two passes without major warping
- LightBurn Pro license included, a $200 value
- Works on the stand, on top of large objects, or handheld with a safety shield that sets the focus height
- Inline red laser lined up with the cutting laser with no offset
- 5 to 150kHz frequency range found a working setting for every material I tested
- Assembly takes one bolt and two cables, and safety glasses come in the box
- Threaded holes in the work area let you build alignment jigs for batch jobs

### Cons

- No foot pedal or start button, so every job starts from your computer, which is awkward in handheld mode
- The LightBurn calibration step sits at the very end of the online guide, and the paper manual doesn't cover LightBurn setup
- No autofocus, though the dual red-dot focus takes a second or two
- Hard to hold with one hand, and it tips backward when resting on the safety shield alone
- LightBurn is the only supported software, with no EZCad instructions
- HansMaker doesn't sell a fume extractor, so you'll need to buy one elsewhere

## Specs

| Spec | Value |
| --- | --- |
| Laser Power | 20W fiber (non-MOPA) |
| Wavelength | 1064nm infrared |
| Work Area | 110 x 110mm (110 field lens, included) |
| Rated Max Speed | 10,000mm/s (1,000 to 4,000mm/s for most of my tests) |
| Pulse Frequency | 5 to 150kHz |
| Precision | Up to 0.001mm (HansMaker's claim) |
| Focus | Electric lifting stand with dual red-dot focus (no autofocus) |
| Positioning | Inline red laser through the galvo |
| Weight | 7.5kg |
| Software | LightBurn (Pro license included) |
| Connectivity | USB Type-B, plus an RJ45 port for the optional rotary |

## Where to buy

- [HansMaker F1 Pro 20W Fiber Laser Engraver](https://hansmaker.com/collections/machine/products/hansmaker-f1-pro-20w-fiber-laser-engraver?aff=6)

Prices may have changed since this review.

## FAQ

### Is the HansMaker F1 Pro worth it?

For a 20W fiber laser, it performed near the top of its class in my month of testing. It deep engraved brass, cut thin steel sheet, gave clean plastic engraving and produced stainless steel colors I'd only seen on MOPA lasers. It sold for $1,479 at the time of recording, and the included LightBurn Pro license adds value. The main drawback is that there's no foot pedal or start button.

### What materials can the HansMaker F1 Pro engrave?

As a 1064nm fiber laser, it works on almost all metals (steel, aluminum, brass, titanium) and plastics, plus darker natural materials like stone and leather. I tested coated and bare aluminum, brass, stainless steel, black acrylic and slate. It doesn't work on wood or on transparent materials like clear acrylic and glass.

### Can the HansMaker F1 Pro make colors on stainless steel?

Yes. By varying power, line interval and frequency, I got greens, magentas, blues, reds, purples and more on stainless steel. It might have the best color results I've seen from a non-MOPA fiber laser.

### Does the HansMaker F1 Pro come with LightBurn?

Yes. HansMaker includes a LightBurn Pro license, a $200 value, and LightBurn is the only software it documents. You need to enter the calibration values from the engraved aluminum card that comes with your machine into LightBurn's Device Settings, or shapes will come out distorted and the wrong size.

### Can the HansMaker F1 Pro cut metal?

It can cut thin sheet metal. It cut through 0.1mm stainless steel sheet in two passes without major warping. Thin sheet is the only cutting I tested. On thicker stock I used multiple passes for deep engraving into aluminum and brass.

---

This HansMaker F1 Pro was provided by HansMaker for review. HansMaker didn't pay for this review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.
