# Sunlu AMS Heater Hands-On: Dry Filament While You Print

Sunlu AMS Heater hands-on with the Bambu Lab AMS. Install, drying modes, thermal tests, and why it won't fit the AMS 2 Pro. See if it fits your setup.

- Author: Chris Hoffman (Hoffman Engineering)
- Published: 2025-08-04
- Category: 3D Printers
- Video: https://www.youtube.com/watch?v=TcsJWoi-wlk
- Web page: https://www.hoffman.engineering/blog/sunlu-ams-heater-hands-on-dry-filament-while-you-print/

## Summary

- Product: Sunlu AMS Heater
- Price: $79.99 at time of review
- Verdict: A first look at a pre-production unit. If you own a first-generation Bambu Lab AMS and want to dry filament while you print, the Sunlu AMS Heater did that well in testing. It does not fit the AMS 2 Pro.

If you've ever had a multi-material print fail because of wet filament, you know the problem: the original Bambu Lab AMS has no way to dry the spools sitting in it. The **Sunlu AMS Heater** is a replacement lid that adds heating to the AMS, so you can dry filament while you print. This hands-on covers installation, both drying modes, thermal testing on a Bambu Lab X1 Carbon, and the fit problem on the AMS 2 Pro, after about a month with a pre-production unit.

## What the Sunlu AMS Heater Does

The heater swaps in for the AMS's factory lid. It keeps a working hinge, so you still lift it open to get to your spools. Without it, drying filament for the original AMS means running each spool through a separate dryer before you print. Dry filament gives you better print quality and fewer failures, so building that into the AMS is the whole appeal.

My unit is pre-production, and it shows. The outside is covered in a mostly opaque black frosted film, which hides the colors of the spools inside. Sunlu told me production units get a transparent area on the front so you can still see what's loaded.

The touch screen sits on the front. Up top is a manual slider vent: open it during the first dry to let moisture out, then close it to keep moisture from coming back in. The power cable and main power switch are on the back.

## Drying Modes: Material Presets and Humidity Control

There are two ways to run the Sunlu AMS Heater.

**Material preset mode** heats to a set temperature for a set time. Presets cover **PLA, PETG, TPU, ABS, Nylon and Polycarbonate**, and you can adjust the temperature anywhere from **35 to 70°C** and the timer from **1 to 99 hours**. You can switch the display to Fahrenheit if you prefer.

**Relative humidity (RH) mode** is the set-and-forget option. You pick a trigger point between 25 and 50% RH. When the humidity inside the AMS reaches it, the heater kicks on and runs until humidity drops below 20%, then turns off and waits. That keeps filament dry for as long as it sits in the AMS.

Inside, two fans push air through **two separate heater units**, venting it around the tops of the spools. One heater sits between slots 1 and 2 and the other between slots 3 and 4, so no single spool sits right next to a heat source. My unit's heater housing is transparent to show off the internals; Sunlu says the final version will be more opaque.

## Installing the Heater on a Bambu Lab AMS

For testing, I visited my friends Skip and Chuck at [Midlife Garage](https://www.youtube.com/@midlife-garage), who let me use their Bambu Lab X1 Carbon. They had both a first-generation AMS and the newer AMS 2 Pro, which turned out to matter.

Installation is quick. Use the included Allen wrench to unscrew the factory hinges, lift the stock lid off, set the Sunlu AMS Heater in its place, and screw on its hinges. That's the whole job. On the original AMS it drops into the groove around the top and seals well.

The hinge is the weak spot on this pre-production unit. It felt unsupported, and I wasn't comfortable opening the lid all the way and letting it hang on the hinge alone. Sunlu told me production units get a reinforced hinge.

## Does the Sunlu AMS Heater Fit the AMS 2 Pro?

No. The AMS 2 Pro is physically wider than the original AMS: **14 and 3/16 inches** compared to **14 inches**. The Midlife Garage guys caught that difference. On the AMS 2 Pro, the heater doesn't sit in the groove and rests on the latches instead.

Some of Sunlu's early marketing mentioned AMS 2 Pro support, but that has since been removed from their website, which makes sense. Treat this as an upgrade for the **first-generation AMS** only.

## Thermal Testing: Drying PETG While Printing

I loaded four rolls of PETG and started the PETG preset. The first surprise was the temperature: the preset is set to **50°C**. Most dryers I've tested dry PETG at 60°C. My guess is that Sunlu landed on 50 to dry the filament without softening it, which could cause feeding problems when printing at higher speeds.

The heater reached 50°C fast, in about **5 minutes**. After that it cycled the heaters on and off and held the temperature within roughly **3 degrees** either way.

The spools themselves take longer. After about an hour and a half they were around **43°C**. The good news is how even it was: all four spools read nearly the same temperature, with no noticeable hot spots.

And the printer kept printing the whole time. Color changes worked, there was no sign of softened filament, and after a few hours we had a Midlife keychain and a clean multi-color test.

## AMS vs Heater Humidity Readings

One quirk: the heater and the AMS don't agree on humidity. Shortly after we turned the heater on, it reported humidity in the 20 percent range, while the printer showed the AMS reading in the 40s. After a couple of hours of printing, the AMS reading dropped into the 30s, but that still left about a 10 percent gap between the two sensors.

That doesn't change how the heater performs, but it's worth knowing if you're watching the AMS humidity readout in Bambu's software and wondering why it doesn't match the heater's screen.

## Price and Availability

When I recorded this video, the Sunlu AMS Heater was on pre-order for **$109**, with lower per-unit prices if you ordered 2, 5 or 10 at a time to retrofit several AMS units. Sunlu was aiming to ship the first batch in mid-October and the second in mid-November.

It's now a regular product. At the time of writing, [Sunlu's store](https://store.sunlu.com/products/sunlu-ams-heater-upgraded-your-bambu-ams-save-an-ams-2pro-for-you?sca_ref=6509515.9CIaM1NpXK&sca_source=amsheater) lists it at **$79.99**, marked down from $119.99, with bundles that add a few rolls of filament.

## Verdict: Should You Buy the Sunlu AMS Heater?

These are early impressions after about a month with a pre-production unit, so take them as a first look. The lack of drying is an obvious gap in the original AMS, and the Sunlu AMS Heater fills it. It heats up quickly, moves air well enough to warm all four spools evenly, and let me print multi-color parts while drying with no problems. The timed presets handle the initial dry, and RH mode keeps filament dry over the long term.

If you own one or more first-generation AMS units, I'd recommend it. It costs much less than buying an AMS 2 Pro, and you get to keep drying while you print. If you have an AMS 2 Pro, skip it: it doesn't fit.

The production changes Sunlu promised, a transparent front and a reinforced hinge, address my two biggest complaints about this unit. Keep in mind I haven't tested a production unit to confirm them.

[Check the latest price at Sunlu](https://store.sunlu.com/products/sunlu-ams-heater-upgraded-your-bambu-ams-save-an-ams-2pro-for-you?sca_ref=6509515.9CIaM1NpXK&sca_source=amsheater)

## Pros and cons

### Pros

- Dries filament while you print, with no problems on multi-color prints during testing
- Heated to the 50°C PETG preset in about 5 minutes and held it within about 3 degrees
- All four spools came up to nearly the same temperature, with no noticeable hot spots
- RH mode keeps filament dry indefinitely by cycling the heater on humidity
- Installs in minutes with the included Allen wrench and seals well on the original AMS
- Presets for PLA, PETG, TPU, ABS, Nylon and Polycarbonate, plus manual temperature and time
- Multi-unit bundles cost less per heater if you have several AMS units

### Cons

- Does not fit the AMS 2 Pro, which is wider than the original AMS
- Pre-production hinge felt unsupported when fully open (Sunlu says production units get a reinforced hinge)
- Pre-production cover is mostly opaque, hiding your spool colors (production units get a transparent front)
- Its humidity reading ran about 10 percent lower than the AMS's own sensor
- Spools heat slowly, reaching about 43°C after an hour and a half at the 50°C setting

## Specs

| Spec | Value |
| --- | --- |
| Compatibility | First-generation Bambu Lab AMS (does not fit the wider AMS 2 Pro) |
| Installation | Replaces the AMS lid, attaches with the factory hinge screws |
| Temperature Range | 35 to 70°C (°F display available) |
| Drying Timer | 1 to 99 hours |
| Material Presets | PLA, PETG, TPU, ABS, Nylon, Polycarbonate |
| Humidity (RH) Mode | Turns on at a set 25 to 50% RH, runs until RH drops below 20% |
| Heating | Two fan-driven heater units, between slots 1 and 2 and slots 3 and 4 |
| Venting | Manual slider vent on top |
| Controls | Front touch screen, rear power switch |

## Where to buy

- [Sunlu AMS Heater](https://store.sunlu.com/products/sunlu-ams-heater-upgraded-your-bambu-ams-save-an-ams-2pro-for-you?sca_ref=6509515.9CIaM1NpXK&sca_source=amsheater): $79.99

Prices may have changed since this review.

## FAQ

### Is the Sunlu AMS Heater worth it?

If you have one or more first-generation Bambu Lab AMS units and fight moisture, it adds the drying the original AMS lacks, and it costs much less than buying an AMS 2 Pro. My pre-production unit heated quickly, warmed all four spools evenly, and printed multi-color jobs without trouble while drying.

### Does the Sunlu AMS Heater fit the AMS 2 Pro?

No. The AMS 2 Pro measures 14 and 3/16 inches wide versus 14 inches for the original AMS, so the heater rests on the latches instead of sitting in the groove. It's made for the first-generation AMS.

### Can you print while the Sunlu AMS Heater is drying filament?

Yes. I ran PETG at the heater's 50°C preset while printing multi-color parts on a Bambu Lab X1 Carbon, and color changes worked with no sign of softened filament or other print problems.

### What temperature does the Sunlu AMS Heater dry PETG at?

The PETG preset is set to 50°C. Most dryers I've tested use 60°C for PETG, so Sunlu appears to keep it lower to avoid softening the filament while it feeds through the AMS. You can set anything from 35 to 70°C manually.

### How does the humidity mode work?

In RH mode you pick a trigger between 25 and 50% relative humidity. When the inside of the AMS reaches it, the heater runs until humidity drops below 20%, then shuts off and waits for humidity to rise again.

---

This Sunlu AMS Heater was provided by Sunlu for review. Sunlu did not pay for this review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.
