# WeCreat Lumos Flex Review: Fiber and Diode Laser in One

WeCreat Lumos Flex review: a 15W fiber and 15W diode laser in one enclosed machine. See a month of test results, the LightBurn problems, and who it suits.

- Author: Chris Hoffman (Hoffman Engineering)
- Published: 2026-11-13
- Category: Lasers
- Video: https://www.youtube.com/watch?v=iXlBQ5oUeAM
- Web page: https://www.hoffman.engineering/blog/wecreat-lumos-flex-review-fiber-and-diode-laser-in-one/

## Summary

- Product: WeCreat Lumos Flex
- Price: $1,940 at time of review
- Discount code: hoffmanengineering ($120 off at WeCreat (US and Canada))
- Verdict: A compact, enclosed dual-laser machine where both the 15W diode and the 15W fiber do useful work. It makes the most sense for a small business that wants to work across wood, acrylic, slate and metal on one machine, and can accept slower deep metal engraving, a small work area and WeCreat's MakeIt software instead of LightBurn.

Stainless steel colored by a laser. A fossil carved three millimeters deep into slate. A brass coin that took four hours to engrave. And an acrylic keychain cut with one laser and engraved with another. All of it came off the **WeCreat Lumos Flex**, which starts at $1,940. This WeCreat Lumos Flex review covers a month of testing with both of its lasers, the LightBurn problems I ran into, and whether it's a practical all-in-one machine for a small business.

## Two Lasers in One Galvo Head

The Lumos Flex is a galvo laser. The head stays put, and two small mirrors inside steer the beam across the material. That's how it moves so fast, and it's also why the work area is small: **116 x 116mm**, about four and a half inches square.

Inside the head are two lasers. The **15W blue diode** handles wood, natural materials, dark acrylic and cutting. The **15W fiber** handles metal. Between them you can work on almost any material you put under it.

Most compact dual-laser machines pair a diode with a low-power infrared laser, usually a few watts. That's good for marking metal, but it isn't practical for deep engraving. The Lumos Flex uses a 15W pulsed fiber instead, with enough power to carve into metal. That's the difference I wanted to test.

WeCreat advertises speeds up to 10,000mm/s and a 50 megapixel camera for lining up designs. The whole machine weighs about 7.5kg, or 16.5 pounds, and has a handle on top.

## Setup, Safety, Fumes and Noise

The Lumos Flex arrives mostly assembled. Install the laser module, drop in the bottom plate, peel off the film, and you're running in a few minutes. Focus is a single press of the auto-focus button on the machine.

Fiber and blue diode lasers can both cause permanent eye damage almost instantly, from direct exposure or a strong reflection. The Lumos Flex is enclosed, with an orange protective cover intended to shield you from both laser wavelengths. That makes it much easier to keep an eye on a job, and I had no issues with the enclosure during testing.

For smoke, I paired it with WeCreat's [AirGuard Cube fume extractor](https://wecreattechltd.pxf.io/zzVzbO), which filters the exhaust instead of venting it outside. While cutting a living hinge in birch, my air quality meter never showed PM2.5 above 15 micrograms per cubic meter, only slightly above the room's normal level. The formaldehyde and VOC readings barely moved.

That's one meter and a few tests. I'd still prefer outside ventilation when you can get it, especially for acrylic.

The AirGuard is the loudest part of the setup. From about two feet away I measured **57 dB on low and 64 dB on high**.

## Software: Plan on MakeIt, Not LightBurn

This is the most important thing to know before you buy. Plan on using WeCreat's software, MakeIt.

WeCreat advertises the Lumos Flex as LightBurn compatible, and it comes with a LightBurn configuration. In my testing, LightBurn was close to unusable. Connections dropped. I had to power cycle the laser between every job, and eventually it stopped connecting at all. Worse, I hit positioning errors mid-job. On a birch test grid, one cell shifted about one and a half cells out of position.

I reported it to WeCreat. They told me the machine is "not as well optimized for LightBurn compatibility as it is for our official WeCreat software," that "occasional positioning shifts" may still happen, and that I should wait one to two seconds between clicks to prevent connection issues. I appreciate the response, but waiting between clicks doesn't solve positioning errors mid-job. If LightBurn is essential to your workflow, I can't recommend the Lumos Flex based on my testing.

MakeIt was a different story. The same machine ran every one of my jobs in MakeIt without a single power cycle. It has full controls for both lasers and useful material presets. My favorite feature: click the square on a test grid that looks best, and MakeIt applies those speed and power settings for you.

I have two small complaints. The test generator only creates fill grids, and the design library doesn't clearly label paid designs. I didn't realize one keychain design cost 99 cents until the very end.

## Diode Laser Results: Wood and Acrylic

**Wood.** 3mm birch plywood cut through in **a single pass at full power and 5.4mm/s**, with a best kerf offset of **0.06mm**. A living hinge made with MakeIt's recommended settings for both the engraving and the cut came out great with no adjustments.

Photo engraving needed tuning. MakeIt's defaults were far too aggressive and dug much deeper into the wood than I wanted. Dropping the power to 50 percent and the dwell to 150 gave a much cleaner surface engraving. Import photos as PNGs, too. An image embedded inside an SVG didn't import for me.

**Speed.** WeCreat advertises up to 10,000mm/s, although MakeIt only let me select up to 6,000. The diode's power becomes the limit long before that. Text engraved cleanly at **2,000mm/s**, but at 3,000 and above the laser couldn't leave a usable mark on birch. Detail was excellent, and even the smallest text in my test came out clean.

**Acrylic.** Blue diodes can't directly cut clear acrylic, but dark acrylic works well. 3mm black acrylic cut through in **two passes at full power and 6mm/s**. For engraving, 30 percent power at 250mm/s left a clean surface mark. Slowing to 50mm/s started digging into the material, and at full power it engraved about two millimeters deep.

## Fiber Laser Results: Stainless Steel Colors and Slate

The fiber laser is the reason to buy this machine.

It can create colors on stainless steel by changing the oxide layer on the surface, and different settings produce different colors. At 60 kHz, my test produced reds, blues, greens, browns, purples, golds and oranges by adjusting only laser power and speed. No paint and no added coloring.

On slate, the fiber can go deep. My fossil relief sits about **three millimeters** below the original surface, which gives it more of a carved look than a normal laser engraving.

## Deep Engraving Brass: The Four Hour Coin

This is where 15 watts shows its limit. MakeIt has a 2D-to-3D relief tool that turns a flat image into a depth map, and the fiber carves that map into the metal.

My first spider coin didn't go as deep as I wanted, so I made a second with a deeper engraving. That one goes a couple of millimeters into solid brass, and it took about **four hours**.

So it works. This is deep engraving in metal, not a surface mark. But at 15 watts it's a long production job, not something you'd make while a customer waits.

## Combining Both Lasers on One Project

This is the advantage of having both lasers in one machine. I cut keychains from black acrylic with the diode, then switched to the fiber for the engraving. An all-diode version gives a decent white mark. The fiber version, using MakeIt's black acrylic preset, is noticeably sharper and crisper.

## Batch Production With the Slide Extension

The 116mm work area is fine for keychains and coasters, but it's the first limit you'll hit when a customer wants something bigger. The [Slide Extension](https://wecreattechltd.pxf.io/0GNGjM) stretches it to **520 x 116mm**.

Setup was easy. Two corner jigs, two cables, and the software handles the rest. The camera stitches four pictures together so you can see the whole extension, and in my tests it lined designs up within half a millimeter.

I engraved a Hoffman Engineering sign across the extension with a 3mm border around the design. There was no visible misalignment, and the final size looked spot on. For a small business, this is where the extension earns its place. You can lay out a row of keychains, tags or other products and run them as a batch instead of repositioning each piece.

## Galvo Limitations: Beveled Cuts and Rounded Corners

Besides LightBurn, I ran into two smaller issues, and both come from the galvo mirrors.

First, cut edges aren't perfectly vertical. As the beam moves toward the edges of the work area, it hits the material at a steeper angle and leaves a beveled cut. For most projects that won't matter, but keep precision-fitting parts near the center.

Second, the usable work area has rounded corners, so you can't use the entire square. MakeIt does warn you when a design gets too close.

## Pricing and Which Kit to Buy

When I recorded the video, the Lumos Flex Essential kit was $1,840, down from $2,790. The Rotary Pack added the Rotary Pro for $2,090, and the Super Pack was $2,490 with the Rotary Pro, the Slide Extension and the AirGuard fume extractor. When I checked for this post, WeCreat listed the Essential kit at **$1,940** and the Super Pack at **$2,290**.

Bought separately, the Slide Extension is $399, the [Rotary Pro](https://wecreat.com/products/rotary-for-wecreat-lumos) is $299 and the AirGuard is $279. The [Magnetic Protective Cone](https://wecreat.com/products/magnetic-protective-cone-for-wecreat-lumos) for handheld mode is another $119.

If I were buying for a small business, I'd lean toward the [Super Pack](https://wecreattechltd.pxf.io/k4q4Mz). The Slide Extension makes batch production much more practical, and you'll want either the AirGuard or a way to vent outside. The Rotary Pro adds another category of products, as does handheld mode. If you mostly make small keychains, tags or coasters and already have a plan for smoke extraction, the Essential kit might be all you need.

## Verdict: Should You Buy the WeCreat Lumos Flex?

The WeCreat Lumos Flex is a compact, enclosed dual-laser machine where both lasers pull their weight. The diode handles wood and acrylic, while the fiber produces stainless steel colors and engraves deep into metal. Across a month of testing, MakeIt ran every job without a single power cycle.

The biggest tradeoff is speed. Fifteen watts of fiber can do impressive work, but that brass coin took four hours. If deep metal engraving is your main business, you're going to want more power. My biggest disappointment is LightBurn, which had enough connection and positioning problems that I wouldn't rely on it. The small work area and angled cut edges are limits too, although the Slide Extension helps with the size.

So I can recommend the Lumos Flex to a small business that wants to work across wood, acrylic, slate and metal without buying multiple machines. You're trading some speed and work area for that versatility, and you'll be working in WeCreat's software. The code hoffmanengineering takes $120 off at checkout in the US and Canada.

[Check the latest price at WeCreat](https://wecreattechltd.pxf.io/QYQYbM)

## Pros and cons

### Pros

- A 15W fiber and a 15W blue diode in one compact, enclosed machine, and both do useful work
- Fiber produced reds, blues, greens, browns, purples, golds and oranges on stainless steel
- Deep engraving that goes past a surface mark, about 3mm into slate and a couple of millimeters into brass
- 3mm birch plywood cut in a single pass at full power and 5.4mm/s, with a 0.06mm kerf offset
- You can combine both lasers on one project, cutting with the diode and engraving with the fiber
- MakeIt ran every job for a month without a single power cycle
- Arrives mostly assembled and runs within a few minutes, with one-press auto-focus
- Slide Extension stretches the work area to 520 x 116mm for batch runs, with no visible misalignment

### Cons

- LightBurn was close to unusable, with dropped connections, power cycles between jobs and a positioning error mid-job
- Deep metal engraving is slow at 15W. One brass coin took about four hours
- Small 116 x 116mm work area, and the rounded corners mean you can't use the whole square
- Cut edges are beveled toward the edges of the work area
- MakeIt's default photo engraving settings dug much deeper into wood than intended
- MakeIt's test generator only creates fill grids, and its design library doesn't clearly label paid designs
- The Slide Extension, Rotary Pro and AirGuard Cube all cost extra with the Essential kit

## Specs

| Spec | Value |
| --- | --- |
| Laser Power | 15W pulsed fiber plus 15W blue diode in one head |
| Motion System | Galvo. The head stays put and two mirrors steer the beam |
| Work Area | 116 x 116mm (about 4.5 inches square, with rounded corners). 520 x 116mm with the Slide Extension |
| Rated Max Speed | 10,000mm/s advertised. MakeIt let me select up to 6,000mm/s, and the diode engraved clean text on birch at 2,000mm/s |
| Kerf Offset (tested) | 0.06mm on 3mm birch plywood |
| Focus | One-press auto-focus button on the machine |
| Camera | 50 megapixel, lined designs up within 0.5mm in testing |
| Safety | Enclosed design with an orange protective cover for both laser wavelengths |
| Fume Extraction | AirGuard Cube fume extractor, sold separately or in the Super Pack |
| Noise (tested) | AirGuard Cube measured 57 dB on low and 64 dB on high from about two feet away |
| Weight | About 7.5kg (16.5 lb), with a handle on top |
| Software | WeCreat MakeIt. Advertised as LightBurn compatible, but LightBurn was close to unusable in testing |

## Where to buy

- [WeCreat Lumos Flex Essential](https://wecreattechltd.pxf.io/QYQYbM): $1,940
- [WeCreat Lumos Flex Super Pack (Rotary Pro, Slide Extension and AirGuard Cube)](https://wecreattechltd.pxf.io/k4q4Mz): $2,290
- [WeCreat Lumos Flex Rotary Pack](https://wecreattechltd.pxf.io/DWNW3j)
- [Slide Extension](https://wecreattechltd.pxf.io/0GNGjM): $399
- [AirGuard Cube Fume Extractor](https://wecreattechltd.pxf.io/zzVzbO): $279
- [Rotary Pro](https://wecreat.com/products/rotary-for-wecreat-lumos): $299
- [Magnetic Protective Cone](https://wecreat.com/products/magnetic-protective-cone-for-wecreat-lumos): $119
- [50W Fiber Module Upgrade](https://wecreattechltd.pxf.io/ZVAVKq)

Use code hoffmanengineering for $120 off at WeCreat (US and Canada). Prices may have changed since this review.

## FAQ

### Is the WeCreat Lumos Flex worth it?

It is if your small business needs to work across wood, acrylic, slate and metal without buying multiple machines. Both lasers did useful work in a month of testing. You trade some speed and work area for that versatility, and you should plan on working in WeCreat's MakeIt software. If deep metal engraving is your main business, you're going to want more fiber power.

### Does the WeCreat Lumos Flex work with LightBurn?

WeCreat advertises it as LightBurn compatible and includes a LightBurn configuration. In my testing LightBurn was close to unusable. Connections dropped, I had to power cycle the laser between every job, one cell of a test grid shifted about one and a half cells out of position, and eventually it stopped connecting. If LightBurn is essential to your workflow, I can't recommend the Lumos Flex based on my testing. MakeIt ran every job without a power cycle.

### What materials can the WeCreat Lumos Flex cut and engrave?

The 15W blue diode cut 3mm birch plywood in one pass at full power and 5.4mm/s, and 3mm black acrylic in two passes at full power and 6mm/s. It also engraved both. Blue diodes can't directly cut clear acrylic. The 15W fiber color marked stainless steel, carved a relief about 3mm deep into slate, engraved a couple of millimeters into solid brass and left a crisp white engraving on black acrylic.

### How fast is the WeCreat Lumos Flex in practice?

WeCreat advertises speeds up to 10,000mm/s, although MakeIt only let me select up to 6,000mm/s. The diode's power becomes the limit long before that. Text engraved cleanly on birch at 2,000mm/s, but at 3,000mm/s and above the laser couldn't leave a usable mark. Deep fiber work is much slower. A brass coin engraved a couple of millimeters deep took about four hours.

### Do you need the Slide Extension for the Lumos Flex?

It depends on what you sell. The native work area is 116 x 116mm, which is fine for keychains and coasters. The Slide Extension stretches it to 520 x 116mm, so you can lay out a row of products and run them as a batch instead of repositioning each piece. For a small business I'd lean toward the Super Pack, which includes it along with the Rotary Pro and the AirGuard Cube.

---

This WeCreat Lumos Flex was provided by WeCreat for review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.
