InfiMech TX Review: Enclosed Klipper CoreXY on a Budget

Chris Hoffman · · 5 min read
Play: InfiMech TX Review: Enclosed Klipper CoreXY on a Budget
InfiMech TX
$329
at time of review

A fully enclosed CoreXY printer with load cell leveling and open Klipper access that went from box to first print in five minutes. A strong pick if you want modern features on a budget.

Check price at InfiMech
On this page

The InfiMech TX went from box to first print in under five minutes. It’s a fully enclosed CoreXY 3D printer running native Klipper, with load cells in the bed for automatic leveling and a rated top speed of 500mm/s, for $329 when I reviewed it. In this InfiMech TX review I cover the hardware, the software and a month of test prints, including the one hiccup I ran into.

CoreXY Speed: 500mm/s With Klipper

The TX uses a CoreXY design: two stationary motors and a belt loop move the hotend in X and Y. With the motors on the frame, the moving hotend stays light, which allows acceleration up to 20,000mm/s². Combined with Klipper, that gives the TX print speeds up to 500mm/s.

Klipper’s features keep quality up at that speed. Accelerometers in the hotend and bed sweep through a range of frequencies during calibration and find where the printer naturally vibrates. Input shaping then controls the motors to dampen those frequencies, which removes ghosting and echo where the printer changes direction. Pressure advance helps cut oozing, bulging and shrinkage and improves surface finish.

Volcano Hotend and Direct Drive Extruder

Pull off the magnetic cover and you’ll find an all-metal hotend with a ceramic heat block and a volcano-style nozzle. It reaches 300°C, enough for nylon and polycarbonate. Dual cooling fans on the sides keep up with the speed.

Above it sits the direct drive extruder for 1.75mm filament. The gears are exposed for easy cleaning, and a clear front panel lets you watch the extruder work, which helps when loading and unloading. The PTFE tube runs to a filament runout sensor at the back, next to a spool holder that worked with every spool I tried.

Enclosure, Glass Door and Removable Lid

The TX is fully enclosed, with a glass door that swings open for easy access. Normally the top stays open for airflow, which suits PLA. For materials that like a hotter chamber, such as ABS or nylon, put on the included lid. It attaches with velcro strips front and back, so it’s easy to take on and off.

An LED light bar inside lights the print bed.

Load Cell Bed Leveling

The bed moves on Z and is a magnetic, flexible PEI spring steel plate. Prints stayed put while printing and came off with one flex. My only gripe is the bed alignment screws: the heads are short, and I’d sometimes miss them.

Load cells in the bed handle auto Z-offset and bed leveling. At startup the printer shakes the bed to check the load cells, then raises the bed until the nozzle presses against it, so it knows exactly where the nozzle is. Leveling works the same way, probing points across the bed and compensating for any warp. Two independent Z motors correct side-to-side tilt.

The build volume is 220 x 220 x 250mm. I never felt limited by it.

Touchscreen, Fluidd and Modding

The power supply at the bottom holds the power switch, a USB port and the 64-bit quad core processor that runs the printer. The 4.3 inch touchscreen gives easy access to every setting, and I especially like the thumbnail previews when picking a print.

Connect over WiFi or the Ethernet port and you get Klipper’s network features. The Fluidd interface controls the printer from any browser on your computer or phone, and you can send prints straight from your slicer.

If you like to modify your printers, you can log in as root and control everything installed and running on the TX. The InfiMech TX subreddit and Discord have dedicated users with great mod guides who know this printer inside and out.

Assembly and OrcaSlicer

The TX arrives almost entirely assembled. Screw on the door handle, attach the touchscreen, slide in the spool holder, and you’re done in under 5 minutes. It doesn’t get easier than this.

InfiMech recommends OrcaSlicer, which comes on the included USB drive along with the profiles. Current versions of OrcaSlicer have the TX profiles built in. The profiles range from fine detail with low layer heights to faster drafts, and I never had an issue with them. OrcaSlicer sends files directly to the printer, and its Device tab loads Fluidd so you can manage the printer without leaving the slicer. Any other slicer works too; save the G-code to the USB drive and print from there.

InfiMech TX Test Prints

Most of the filament in this review came from my filament sponsor Sunlu.

  • 3D Benchy: the USB drive has a standard and a high-speed version. The standard one took 44 minutes and is flawless, with great cabin bridging and very little hull line. The high-speed one took 18 minutes and has rougher edges, some stringing and defects on the front of the hull. For up to 500mm/s, it’s still impressive.
  • Torture test: stringing on the last tower, but the rest printed clean all the way up. Even the 15 degree overhangs printed, and bridging only drooped slightly on the longest span.
  • Flexi Rex: printed in 39 minutes and came out perfect, with a consistent bottom layer thanks to the leveling.
  • Flexi T-Rex: printed with the 0.08mm extra-fine profile. It looks close to resin printer quality, and I can hardly see the layer lines.
  • String art: the included sample showed off the bridging from the dual fans. A spider web version I sliced myself printed equally well.
  • Desert Kiss dice tower: 0.16mm layers in 12 hours and 22 minutes. The overhangs held up and the layers on top of the skull are very smooth.
  • Spiral vase mode: a GCreate rocket with no ghosting at feature edges thanks to input shaping, and only minor defects on the antenna.
  • TPU Benchy: printed entirely in TPU. The window and hull overhangs aren’t perfect, but the walls are consistent, and squishing a Benchy is satisfying.

The One Issue I Hit

I confused the load cells once. I started the filament loading feature, then switched back to the move screen before loading began. Thinking I had canceled it, I tried to lower the bed, and it wouldn’t move. So I pressed home, and the bed traveled all the way up without detecting the nozzle.

The bed stopped at the end of the lead screws and the printer wasn’t damaged at all. The lesson: let loading or unloading finish before starting anything else.

Verdict: Should You Buy the InfiMech TX?

I’m very impressed by the InfiMech TX. It made a great first impression with five minutes from unboxing to first print, the included sample prints were varied and high quality, and the OrcaSlicer profiles were easy to set up and gave great results. The CoreXY design makes for fast prints, and Klipper’s input shaping and pressure advance keep quality high at speed.

The TX was $329 when I reviewed it, or $379 bundled with the camera, auxiliary fan and activated carbon filter. If you want a fully enclosed printer with modern features on a budget, the InfiMech TX is the printer for you. If you’re comparing CoreXY printers, see my Two Trees SK1 review.

Check the latest price at InfiMech.

Pros and cons

✓ Pros

  • Less than 5 minutes from unboxing to first print
  • Load cells give automatic Z-offset and bed leveling, with a consistent first layer every time
  • Full enclosure with a glass door, plus a removable lid for ABS and nylon
  • 0.08mm layers on a flexi T-Rex came out close to resin printer quality
  • Native Klipper with input shaping, pressure advance, Fluidd and root access for modding
  • OrcaSlicer has built-in TX profiles and sends prints straight to the printer
  • 300°C hotend and direct drive extruder handle nylon, polycarbonate and TPU
  • Active community on the InfiMech TX subreddit and Discord

✗ Cons

  • Starting a filament load, then leaving the screen confused the load cells, and homing drove the bed to the end of its travel
  • High-speed 18 minute Benchy shows rough edges, stringing and hull defects
  • Bed alignment screw heads are short and easy to miss
  • TPU Benchy overhangs on the windows and hull weren't perfect

Specs

Build Volume220 x 220 x 250mm
Motion SystemCoreXY, bed moves on Z with two independent motors
Max Speed and Acceleration500mm/s, 20,000mm/s²
Hotend Max Temp300°C, all-metal volcano-style hotend with ceramic heater
ExtruderDirect drive, 1.75mm filament
BedMagnetic, flexible PEI spring steel with load cells for auto Z-offset and leveling
EnclosureFull enclosure with a glass door and a removable lid
FirmwareNative Klipper with Fluidd, input shaping and pressure advance, root access
Screen4.3 inch touchscreen
ConnectivityWiFi, Ethernet, USB drive

Where to buy

Prices may have changed since this review.

FAQ

Is the InfiMech TX worth it?

At $329 when I reviewed it ($379 with the camera, auxiliary fan and carbon filter), the TX is a fully enclosed CoreXY printer with load cell leveling and Klipper. It went from box to first print in under five minutes, and the included OrcaSlicer profiles gave high quality prints. If you want a budget-friendly enclosed printer with modern features, it's a strong pick.

How fast can the InfiMech TX print?

It's rated for 500mm/s with 20,000mm/s² acceleration. The included standard Benchy took 44 minutes and came out flawless. The high-speed version took 18 minutes and showed some rough edges and stringing, which is still an impressive result for 500mm/s.

Can the InfiMech TX print ABS, nylon and TPU?

Yes. The hotend reaches 300°C for nylon and polycarbonate, and the included lid closes the top of the enclosure for materials that like a hot chamber, like ABS and nylon. The direct drive extruder handled a Benchy printed entirely in TPU.

What slicer does the InfiMech TX use?

InfiMech recommends OrcaSlicer, which ships on the included USB drive and has the TX profiles built in. OrcaSlicer sends files straight to the printer and its Device tab loads the Fluidd interface. You can use any slicer and print from the USB drive.

This InfiMech TX was provided by InfiMech for review. InfiMech did not pay for this review. This post contains affiliate links. If you purchase through them, I may earn a small commission at no extra cost to you. All opinions are my own.